City Pedia Web Search

Search results

1. Results From The WOW.Com Content Network

2. Wrench size - Wikipedia

   en.wikipedia.org/wiki/Wrench_size

   Sizes that may interchange, depending on the precision needed, include 2 mm (close to 5 ⁄ 64 inch (1.98 mm)), 4 mm (close to 5 ⁄ 32 inch (3.97 mm)) and 8 mm (close to 5 ⁄ 16 inch (7.94 mm)). In reality, a wrench with a width across the flats of exactly 15 mm would fit too tightly to use on a bolt with a width across the flats of 15 mm.

3. List of drill and tap sizes - Wikipedia

   en.wikipedia.org/wiki/List_of_drill_and_tap_sizes

   Schematic of a machine tap. Below is a comprehensive drill and tap size chart for all drills and taps, imperial and metric, up to 36.5 millimetres (1.44 in) in diameter.. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly.

4. British Standard Whitworth - Wikipedia

   en.wikipedia.org/wiki/British_Standard_Whitworth

   British Standard Whitworth(BSW) is an imperial-unit-based screw threadstandard, devised and specified by Joseph Whitworthin 1841 and later adopted as a British Standard. It was the world's first national screw thread standard, and is the basis for many other standards, such as BSF, BSP, BSCon, and BSCopper. History.

5. Drill bit sizes - Wikipedia

   en.wikipedia.org/wiki/Drill_bit_sizes

   For Morse taper-shank drill bits, the standard continues in 1/64 inch increments up to 1¾ inch, then 1/32 inch increments up to 2¼ inch, 1/16 inch increments up to 3 inches, 1/8 inch increments up to 3¼ inches, and a single 1/4 inch increment to 3½ inches. One aspect of this method of sizing is that the size increment between drill bits ...

6. 3-inch/50-caliber gun - Wikipedia

   en.wikipedia.org/wiki/3-inch/50-caliber_gun

   Sights. Peep-site and Optical telescope. The 3-inch/50-caliber gun (spoken "three-inch fifty-caliber") in United States naval gun terminology indicates the gun fired a projectile 3 inches (76 mm) in diameter, and the barrel was 50 calibers long (barrel length is 3 in × 50 = 150 in or 3.8 m). Different guns (identified by Mark numbers) of this ...

7. Socket wrench - Wikipedia

   en.wikipedia.org/wiki/Socket_wrench

   For example, a 1 ⁄ 4-inch to 3 ⁄ 8-inch adapter allows sockets with 1 ⁄ 4-inch drive holes to attach to a 3 ⁄ 8-inch ratchet, and so on. Universal joints are two articulated socket joints (about 1 inch (25 mm) long) combined at a right angle, that allow a bend in the turning axis of the wrench and socket. They are used with extensions ...

8. Unified Thread Standard - Wikipedia

   en.wikipedia.org/wiki/Unified_Thread_Standard

   The standard designation for a UTS thread is a number indicating the nominal (major) diameter of the thread, followed by the pitch measured in threads per inch.For diameters smaller than ⁠ 1 / 4 ⁠ inch, the diameter is indicated by an integer number defined in the standard; for all other diameters, the inch figure is given.

9. List of culinary knife cuts - Wikipedia

   en.wikipedia.org/wiki/List_of_culinary_knife_cuts

   Fermière; cut lengthwise and then sliced to desired thickness 1 ⁄ 8 – 1 ⁄ 2 inch (3–10 mm) Rondelle; cylindrical vegetables cut to discs of desired thickness 1 ⁄ 8 – 1 ⁄ 2 inch (3–10 mm) Tourné; 2 inches (50 mm) long with seven faces usually with a bulge in the center portion; Mirepoix; 3 ⁄ 16 – 1 ⁄ 4 inch (5–7 mm)